Set up your cleats before a bike fit
Your cleats are the foundation of your bike fit. How to set their position, angle, width and float before you film with the Bike Fitting Tool.
Your cleats are the foundation of your bike fit. Get them right before you film with the Bike Fitting Tool.
Why cleats come first
Your feet are where all your power reaches the bike. Your cleats decide three things: where your foot sits over the pedal axle, which way it points, and how far apart your feet are. Change any of them and your leg reaches the pedal differently, so your knee and hip angles change too. That changes what the right saddle height is.
The Bike Fitting Tool measures your leg angles from video, but it can't see your cleats. If you set the saddle first and move your cleats afterwards, the saddle height you dialed in no longer fits. So:
- Set up your cleats (this article).
- Ride them two or three times, so you know they feel right.
- Then do your fit.
Changed your cleats after a fit? Start a new round in the Bike Fitting Tool so it measures your new position.
Before you start
- Trace your cleats as they are now. Draw around each cleat on the sole with a fine marker. If a change doesn't suit you, you can always go back.
- Check they aren't worn. Many road cleats have wear indicators. Replace them if the indicator has worn away, the cleat rocks on the pedal, or your foot unclips when you don't mean it to. A worn cleat moves under you and makes every measurement less reliable.
- You'll need: a hex key or screwdriver for the cleat bolts (a torque wrench if you have one), a marker, and a strip of masking tape.
1. Fore-aft: where your foot sits over the pedal
Start with the pedal axle under the ball of your foot, or just behind it.
- Put your shoe on and find the bony bump at the base of your big toe (the ball of your foot). Put a strip of masking tape on the side of the shoe and mark where the bump is.
- Find the bony bump at the base of your little toe and mark that on the outside of the shoe.
- Take the shoe off, turn it over and draw a line across the sole between the two marks.
- Most cleats have a mark on each side showing where the pedal axle sits. Line those marks up with the middle of your line, or up to about 5 mm behind it (toward the heel).
Go a little further back if your toes go numb or burn ("hot foot"), or your calves or Achilles get tight on long rides. A cleat further back puts less load on your calf and spreads pressure away from the ball of the foot.
If you move your cleats back noticeably, your saddle usually has to come down a little, about 1 mm for every 3 mm of cleat movement, because your foot now sits further forward over the pedal. Your fit will check this from the video.
2. Rotation: which way your feet point
Set each cleat so your foot points the way it naturally wants to.
- Sit on a table or a high counter with your lower legs hanging loose.
- Look at your feet. Most people's heels point slightly in and toes slightly out, and often one foot more than the other. That's normal.
- Angle each cleat so the shoe sits on the pedal at that same angle.
- On the bike, clip in, pedal easily and let your feet settle. Then gently swing each heel in and out. Your foot should sit in the middle of the cleat's free movement (its "float"), not pressed against one end.
Also check that your heel doesn't brush the crank arm, and that your ankle bone doesn't touch the crank.
3. Side to side: how far apart your feet are
Start with the cleat centered side to side on the sole.
When you pedal, your knees should travel roughly straight up and down over your feet. If your knees track noticeably outside your feet, a slightly wider stance may suit you. If you feel squashed together at the hips, the same applies.
- Moving the cleat toward the inside of the sole moves your foot outward (a wider stance).
- Moving it toward the outside of the sole moves your foot inward.
Move 1–2 mm at a time, and keep both feet the same unless you know one side is different. If you need more width than the cleat allows, pedal axle spacers or longer-axle pedals can add it.
4. Float: how much your foot can twist
Float is how far your heel can swing before the cleat starts to release. Some float lets your knee follow its natural path instead of being forced into a fixed one, and research on pedals with float shows lower twisting loads on the knee.
- Road cleats usually come in fixed (0°), small (about 2–4.5°) and more float (about 6–9°). The cleat's color tells you which; check the maker's chart.
- Most riders do best with some float. If you get pain on the inside or outside of the knee, try more float before anything else.
- Fixed cleats suit riders who know they want them, usually track and sprint riders.
- Two-bolt cleats (SPD and similar, on gravel and mountain bike shoes) follow the same ideas. They have less room to adjust, and their float and release are set by the cleat type and the pedal's spring tension.
5. Tighten and check
- Tighten each bolt a little at a time, going back and forth between them, so the cleat sits flat.
- Finish at the torque in the cleat's instructions (usually 4–6 N·m). Too loose and the cleat slips; too tight and you can strip the threads in the shoe.
- Trace around the cleats again in their new spot.
- Clip in and out a few times on each side before you ride.
6. Ride them in, then do your fit
Ride your cleats two or three times, or a couple of hours, before you film. Change one thing at a time, in small steps (1–2 mm or 1–2°), so you can tell what helped. Once they feel right, leave them alone and start your fit: Bike Fitting Tool → Start a fit in the app.
Signs your cleats need attention
- Hot, burning or numb toes: move the cleats 2–3 mm back, and loosen the shoe's front strap or dial.
- Calf or Achilles tightness: move the cleats a little back.
- Pain on the inside or outside of the knee: check the rotation (step 2) and try more float (step 4).
- Knees flaring out, or feeling cramped at the hips: try a slightly wider stance (step 3).
- Heel hitting the crank: rotate the cleat so the heel moves out, or widen the stance.
- Foot sliding or twisting on the pedal: look for a worn cleat, loose bolts or too little release tension.
When to see a professional fitter
The Bike Fitting Tool and this article cover the usual cleat setup. See a professional fitter in person if:
- one leg is noticeably shorter, or one foot sits very differently from the other
- your feet roll in or out a lot (arches that collapse, or very high arches); wedges, shims or custom insoles may help, and those are best fitted in person
- pain carries on after a few small changes
This is guidance for comfort and performance, not medical advice. If something hurts sharply, gets worse or carries on off the bike, see a doctor or physiotherapist.
Was this helpful?